Apeks XTX Cover Tool

[Mike1967]

No flow is 1mm and flow is 2mm.

 

[HeXx]

No flow is 1mm and flow is 2mm.

Hi.
Sorry for my lousy finger painting on those.
If you could please provide measurements in both GAS side and NO GAS.
1 and 2 are depth from base to outer lip.
3 os thickness of the lip.
4 and 5 are full with and heigh measured from the outside of the lip.
And finally 6 is the distance from the top of the lip to that side step.

Once I make the 3D object I will post it here and test with my XTX50's

Cheers

 

[admikar]

GAS
1. 7.8 mm
2. 12.8 mm
3. 1.9 mm (note: at the top, lip thickness warries as it is wider at the bottom)
4. 18.2 mm
5. 53.6 mm
6. 1.9 mm ( side step drooping towards lip)
NO GAS
1. 8.0 mm
2. 13.0 mm
3. 1.9 mm
4. 18.2 mm
5. 53.6 mm
6. 1.3 mm

 

[HeXx]

GAS
1. 7.8 mm
2. 12.8 mm
3. 1.9 mm (note: at the top, lip thickness warries as it is wider at the bottom)
4. 18.2 mm
5. 53.6 mm
6. 1.9 mm ( side step drooping towards lip)
NO GAS
1. 8.0 mm
2. 13.0 mm
3. 1.9 mm
4. 18.2 mm
5. 53.6 mm
6. 1.3 mm

Thank you very much for your trouble.
It seems to me that what defines the depth at which the purge button is pressed is the lip eight on measurement 6. Could you check on your reg if that's where the part ends travel when pressed against the reg?

Thank you.

 

[Mike1967]

It seems to me that what defines the depth at which the purge button is pressed is the lip eight on measurement 6.

That's right, looks like I was out a bit using a steel rule lol
That's why I didn't reply after you wanted to know all the measurements

 

[Bubble_Joe]

Hi.
Sorry for my lousy finger painting on those.
If you could please provide measurements in both GAS side and NO GAS.
1 and 2 are depth from base to outer lip.
3 os thickness of the lip.
4 and 5 are full with and heigh measured from the outside of the lip.
And finally 6 is the distance from the top of the lip to that side step.

Once I make the 3D object I will post it here and test with my XTX50's

Cheers

Hi
Did you already make an 3D Model for the tool? I would be interested to try it.
Cheers

 

[MB NZ]

 

[Tritontaucher]

Hi.
Sorry for my lousy finger painting on those.
If you could please provide measurements in both GAS side and NO GAS.
1 and 2 are depth from base to outer lip.
3 os thickness of the lip.
4 and 5 are full with and heigh measured from the outside of the lip.
And finally 6 is the distance from the top of the lip to that side step.

Once I make the 3D object I will post it here and test with my XTX50's

Cheers

Hi togehter, i am new on this forum. I am looking at the thingiverse file for the tool within the version Gas side an No gas side for Apeks XTX front cover both editions. The file into thingiverse is only the front cover tool without the options Gas side / No gas side.

 

[Tritontaucher]

Apeks XTX Edition old version until 2012 has been changed 2013 to the new design
The thingiverse file matches only for the 2013 edition.

 

[Tritontaucher]

Thank you very much for your trouble.
It seems to me that what defines the depth at which the purge button is pressed is the lip eight on measurement 6. Could you check on your reg if that's where the part ends travel when pressed against the reg?

Thank you.

Did you already make an 3D Model for the Apeks XTX Front cover tool within the version Gas / no gas.
for Apeks edition 2012 (old version ) and 2013 (new version?)