A repository of 3D print STL sources

[Simpel]

Hello,

Has anyone developed a compass holder with a mount for a light to illuminate the compass?

V3 LED FLEXI-LIGHT STICKS (8 LUMENS)

www.emergencyuk.com

 

[Timmyjane]

Uploaded a new thing to aid in the removal of the Scubapro splined barrel nuts.

Scubapro Spline Socket Wrench Adapter Tool by timmyjane

Adapter to remove Scubapro splined nut from G250 barrel. I am sure it'll worok on other models as well. Included imperial and metric socket adapters. Larger tool has a 14mm/9/16 fitting.

www.thingiverse.com

 

[TMurrr]

Anyone have a 'cover' for a Garmin Mk2i?

The idea is some plastic piece to clip over the watches screen to protect it while its off/unused.

For what its worth I'm incredibly forgetful so everything gets attached/clipped to my BCD when I'm not diving. It makes rinsing, storing and remembering much easier but I'd like to put a cover in between the Mk2i's face and everything else, while its not in use.

 

[Timmyjane]

Uploaded a new thing to aid in the removal of the cap on Scubapro Regulators. A pin spanner tool. There are 2 versions.

Scubapro 1st Stage Pin Spanner Cap Removal Tool by timmyjane

Spanner tool to aid in the teardown of a Scubapro 1st stage regulator. 9/16 14mm socket/wrench point on top for leverage if needed. Once printed use (2) 2.5 x 12 mm machine screws with nuts or (2) 2.0 x 12 screws with nuts depending on which model you choose.The holes are very tight on the...

www.thingiverse.com

 

[Timmyjane]

Scubapro Piston Bullet O Ring Assembly tool.

If y'all can't tell Ive collected a bunch of Scubapro regulators and am learning to rebuild and set them up. Having to make tools as I go.

Scubapro Piston Bullet O Ring Assembly Tool by timmyjane

Tool to assemble Scubapro balanced piston regulators such as MK5, MK7, MK10 and others. Keeps the knife edge of the piston from cutting or damaging internal o ring when installing the piston.

www.thingiverse.com

 

[Timmyjane]

Posted a remix of the mouthpiece adapter found HERE.

Made the mouth end a little smaller and moved the hose connection 90 degrees as discussed in the original post.

Magnehelic Mouthpiece Adapter by timmyjane

Redesigned the original Magnehelic Mouthpiece Adapter uploaded by Ryninger. Perhaps a more comfortable mouth piece and moved the tube connection 90 degrees.

www.thingiverse.com

 

[Timmyjane]

Scubapro MK10 Internal O-Ring Installation Tool
Another version on Thingiverse did not work so I had to make one that did. I have installed a couple of o rings successfully now with this set.

Scubapro MK10 Internal O Ring Installation Tool with Piston Bullet by timmyjane

This design works for the MK10. I have successfully installed several internal o-rings with this tool.

www.thingiverse.com

 

[Timmyjane]

Orifice push rod tool.

2nd Stage SCUBA Regulator Orifice Push Rod by timmyjane

Push rod to remove the orifice from a second stage regulator. This works for my ScubaPro G250s. I am sure it will work for many others also.

www.thingiverse.com

 

[Timmyjane]

Designed to aid in servicing piston 1st stage regs.

1st stage SCUBA Regulator Piston Edge Restoring Polishing jig by timmyjane

Install a 010 Duro 90 O Ring in the top piece.Lubricate as o ring and piston shaft as required.Use piston bullet to install through o ring.Uses AZDental HP 0412 Denture Polishing Kit to polish the inside of the piston. I found that the blunt nosed polisher fits best inside the piston. (See...

www.thingiverse.com

MK10 servicing thread:

MK10 Rebuilding Mods and Best Practices

I have several MK10s to service. I have come across a few comments here and there such as: Remove the polished surface from the piston stem o-ring. Micro-mesh the piston hard seat. These comments were made as modifications to try. I don't know what they mean or what improvement these...

scubaboard.com

 

[BigGixx]

Did anyone get a good copy of the DIN Silencer?