That's precisely the point.Yes of course I can but that's not the point.
Welcome to ScubaBoard, the world's largest scuba diving community. Registration is not required to read the forums, but we encourage you to join. Joining has its benefits and enables you to participate in the discussions.
Benefits of registering include
That's precisely the point.Yes of course I can but that's not the point.
I know exactly what you mean. On the Suzuki's there is a known problem on the lanyard kill switch with it sticking/corrosion. With the key off it may take a couple times of installing/removing the little red fork on the lanyard to get the kill switch 'nub' to reset. Like you said, you can do fuses, batt cables, throttles, & everything and nothing works. It's that kill switch nub that the red fork goes under and it needs to be replaced.Luckily, and for no apparent reason after 10-15minutes, the captain was able to start the motors and came over to pick me up...
Then why have any debates or discussion on this forum? Science doesn't matter. Skills and experience don't matter. People should just do what they want because it's their neck. According to you.
Since nobody has come up with the correct scenario and this thread is diverging all over the place, maybe it is time to finish the story before everyone forgets where I left off.
Even though my buddy has two brand new engines (less than 20 hrs) he has had some issues with the engines failing to start. I had never experienced it when I was operating the boat, nor had it occurred when either of use were diving and a recent modification/trip-to-shop, lead us to believe that the previous issue had been completely resolved,
However, apparently while I was diving, he turned both engines off and neither would even turn over or start. The trim worked but the engines acted like they were not in neutral which electronically precludes starting. He checked fuses, shut off the power, switched batteries and tried everything he could think of.
So he was kinda freaking out because he is dead in the water and I am drifting away with the float ball continuing my dive, oblivious to any problems topside. He noticed this fisherman in the area and (apparently there was enough communication established, since he speaks some Spanish) to request that the fisherman, go over, grab the float and then pull me in so I would not be lost.
That is exactly what the nice fisherman did, however, I was ignorant of the situation, not able to communicate, unhappy and was not even considering the option to possibly board his boat. At least I didn’t cuss him out.
Luckily, and for no apparent reason after 10-15minutes, the captain was able to start the motors and came over to pick me up (as I resumed drifting on the surface for just a minute or so).
My buddy had thrown out his anchor earlier when the initial problem occurred, to prevent drifting too far. When the engines eventually started, he just ditched it (rather than haul it all in on the boat by himself) in order to recover me ASAP.
It took me two more dives to find and then recover the anchor and line he ditched, I asked him to leave the engines running while I did these dives, LOL.
Six drops yesterday, I went to bed early last night.
Wonder if the nice fisherman will ever try to help out a few divers again?
Have you checked the neutral safety switch? I have a suzuki snd it's very touchy. I replaced the switch and it didn't help.Since nobody has come up with the correct scenario and this thread is diverging all over the place, maybe it is time to finish the story before everyone forgets where I left off.
Even though my buddy has two brand new engines (less than 20 hrs) he has had some issues with the engines failing to start. I had never experienced it when I was operating the boat, nor had it occurred when either of use were diving and a recent modification/trip-to-shop, lead us to believe that the previous issue had been completely resolved,
However, apparently while I was diving, he turned both engines off and neither would even turn over or start. The trim worked but the engines acted like they were not in neutral which electronically precludes starting. He checked fuses, shut off the power, switched batteries and tried everything he could think of.
So he was kinda freaking out because he is dead in the water and I am drifting away with the float ball continuing my dive, oblivious to any problems topside. He noticed this fisherman in the area and (apparently there was enough communication established, since he speaks some Spanish) to request that the fisherman, go over, grab the float and then pull me in so I would not be lost.
That is exactly what the nice fisherman did, however, I was ignorant of the situation, not able to communicate, unhappy and was not even considering the option to possibly board his boat. At least I didn’t cuss him out.
Luckily, and for no apparent reason after 10-15minutes, the captain was able to start the motors and came over to pick me up (as I resumed drifting on the surface for just a minute or so).
My buddy had thrown out his anchor earlier when the initial problem occurred, to prevent drifting too far. When the engines eventually started, he just ditched it (rather than haul it all in on the boat by himself) in order to recover me ASAP.
It took me two more dives to find and then recover the anchor and line he ditched, I asked him to leave the engines running while I did these dives, LOL.
Six drops yesterday, I went to bed early last night.
Wonder if the nice fisherman will ever try to help out a few divers again?
I'll admit, I didn't read the thread all that carefully, but... A floatball has no standing. A dive flag on the other hand means something. Where was the boat that put you in the water?I am pulling a floatball ...
I'll admit, I didn't read the thread all that carefully, but... A floatball has no standing. A dive flag on the other hand means something. Where was the boat that put you in the water?