HalcyonDaze
Contributor
I have my pony filled with 30% nitrox, because on my deepest dives these days that's what I put in my main tank. I haven't been an adherent of the 1.4 limit since I got my nitrox cert back in 2005; I treat 1.6 as a never-exceed and try to give myself a little bit of room for error. These days the bottom is at about 135-140 on the deepest site I hit and I haven't gone deeper than 136, which I was probably at for a minute at most.
My rationale was the same as boulderjohn stated - if I'm close to NDL when I need to bug out, I'd rather have a little extra cushion against DCS even if my calculations are factoring in a normal ascent rate and a safety stop. That said, every time I open the valve, test the reg before the dive, and then purge it after shutoff that's taking a little gas out. With air I could just top it off regularly, as opposed to having to completely drain and refill it with nitrox when it goes under par.
I would think 9 minutes was the total time from when he left the surface and not how long he was at depth. When I selected a 19 cf tank as my bailout, it was after I had run the numbers through an Excel spreadsheet provided by a tech diver. Assuming a base SAC of 0.8 cf/min, ascending at 30 ft/min, and taking a 3 min safety stop at 15 ft, coming up from 140 ft would consume about 15.5 cf of gas - roughly 82 percent of the tank's gas, leaving me with a little over 500 psi. That's after 7-8 minutes of ascending or hanging at 15 ft, not remaining at 110-133 ft.
For another example from the near miss section, some time ago a poster put up a video of himself using an underfilled (~2,500 psi) 13 cf pony bottle to dive down and get a weight belt at 85 ft. The descent took about a minute and it was another minute on the bottom before he recovered the belt, after which he had 1,300-1,400 psi left. He then took two minutes to ascend and got back up top with a little under 1,000 psi. Run the numbers and he burned about 4-5 cf of gas in 2 minutes descending to and leveling off almost 50 ft shallower than where the victim in this case was going.
My rationale was the same as boulderjohn stated - if I'm close to NDL when I need to bug out, I'd rather have a little extra cushion against DCS even if my calculations are factoring in a normal ascent rate and a safety stop. That said, every time I open the valve, test the reg before the dive, and then purge it after shutoff that's taking a little gas out. With air I could just top it off regularly, as opposed to having to completely drain and refill it with nitrox when it goes under par.
I find it unlikely that using 32% for 9 minutes at 130 ft is going to cause someone to pass out. Possible, but unlikely.
I would think 9 minutes was the total time from when he left the surface and not how long he was at depth. When I selected a 19 cf tank as my bailout, it was after I had run the numbers through an Excel spreadsheet provided by a tech diver. Assuming a base SAC of 0.8 cf/min, ascending at 30 ft/min, and taking a 3 min safety stop at 15 ft, coming up from 140 ft would consume about 15.5 cf of gas - roughly 82 percent of the tank's gas, leaving me with a little over 500 psi. That's after 7-8 minutes of ascending or hanging at 15 ft, not remaining at 110-133 ft.
For another example from the near miss section, some time ago a poster put up a video of himself using an underfilled (~2,500 psi) 13 cf pony bottle to dive down and get a weight belt at 85 ft. The descent took about a minute and it was another minute on the bottom before he recovered the belt, after which he had 1,300-1,400 psi left. He then took two minutes to ascend and got back up top with a little under 1,000 psi. Run the numbers and he burned about 4-5 cf of gas in 2 minutes descending to and leveling off almost 50 ft shallower than where the victim in this case was going.
Last edited: