Effect of gas density while deep diving

Please register or login

Welcome to ScubaBoard, the world's largest scuba diving community. Registration is not required to read the forums, but we encourage you to join. Joining has its benefits and enables you to participate in the discussions.

Benefits of registering include

  • Ability to post and comment on topics and discussions.
  • A Free photo gallery to share your dive photos with the world.
  • You can make this box go away

Joining is quick and easy. Log in or Register now!

131 feet on air has a gas density of 6g/L.
131 feet = 39.9 meters. At an ATA of 4.9, air with a density at 1 ATA of 1.293 gives you 6.5 g/L, beyond the absolute max recommended of 6.2 (http://alertdiver.com/Gas-Density).

This whole discussion is making me rethink how soon I use helium, as I figure continuing a normalization of deviance is going to catch up to me. Spending a bit on helium is cheap when considering I have a wife and daughter now.
 
131 feet = 39.9 meters. At an ATA of 4.9, air with a density at 1 ATA of 1.293 gives you 6.5 g/L, beyond the absolute max recommended of 6.2 (http://alertdiver.com/Gas-Density).

This whole discussion is making me rethink how soon I use helium, as I figure continuing a normalization of deviance is going to catch up to me. Spending a bit on helium is cheap when considering I have a wife and daughter now.
No problem, MultiDeco gave me 6.0 for each
upload_2019-10-28_19-22-45.png
upload_2019-10-28_19-23-7.png
 
They rounded down the gas density from 1.293 down to 1.2. For something like this, I would hope that they'd round up to 1.3 instead.

That's nuts. Thanks for pointing out. It's got to be more than just rounding off the 1.293 for air to 1.2 because MultiDeco seems to get this wrong for other mixes, not just air.

For example, a 16/50 mix at 250' yields a gas density of 5.9 in MultiDeco but 6.37 using the gas density calculator spreadsheet.

I feel like I'm missing something here....
 
That's nuts. Thanks for pointing out. It's got to be more than just rounding off the 1.293 for air to 1.2 because MultiDeco seems to get this wrong for other mixes, not just air.

For example, a 16/50 mix at 250' yields a gas density of 5.9 in MultiDeco but 6.37 using the gas density calculator spreadsheet.

I feel like I'm missing something here....
I sent a message with a link to this thread, so hopefully Ross will read this thread.
 
Ross's response (he mentioned being banned, but was kind enough to respond):


The sample equation is off. 39.9m is not 4.9 ATA - that is divers
rounding at work. 39.9m of salt water, at sea level, is 4.96 ATA =
(39.9/10.078) + 1. This slight variation in ATA values used, is a
common error in "diver rounded" calculations.

Gas density is easily seen at sites like this:
Gases - Densities

The Alert Diver values agree with those above, but they list the STP
values at 0° C (32F). However, our program uses the 20°C values, which
are more realistic for human consumption. If there was a 30°C set of
values available, we would use those instead.

Air @ 20°C = 1.205 g/l/ATA
1.205 * 4.96 = 5.97 == 6.0.

The water vapor content and the gas temperature at the restriction
point, is debatable, and they both affect the calculation.

There is no rounding of data in our program, but different
interpretations of the problem and a gasses density gives a slightly
different answer.


Please post this in full.


Regards
--
Ross Hemingway
HHS Software
Kingston ON Canada
HHS Software Corp.
 
http://cavediveflorida.com/Rum_House.htm

Back
Top Bottom