АлександрД
Contributor
once I bought Sea&Sea YS-27 and had look for cable for it...
special cables had stupid price around 60$ per small piece of plastic....
I take:
Digital Optical Fiber Audio Cable SPDIF Toslink (price could be from 2-4$)
Heat Shrink tubeS (price for set of different diameters is around 1-2$)
knife (I had)
Lighter or Hot air solderer
Cut optical cable to the desired lenght (cut away connectors anyway)
Put on thinest tube, with length 2-4 cm (1/2 till 1 inch), heating it.
Than more thick, and shorter. Heat it.
etc.
at final steps:
Cool it well, than cut front edge with sharp knife.
Heat it again, and then push it in-to connecting hole and bent over, to fit exact size.
![i-720.jpg i-720.jpg](https://scubaboard.com/community/data/attachments/392/392085-c58fafb8bd7607c50ca37357b0bf27a9.jpg)
Also can bent hot cable.
![i-716.jpg i-716.jpg](https://scubaboard.com/community/data/attachments/392/392082-5e7c592bf7c1c6703d16c2c9184aeefc.jpg)
Wait untill it be cold, and use and be happy![Smile :) :)](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
If you got bad selfmade connector - just cut away, and repeat![Smile :) :)](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
![i-718.jpg i-718.jpg](https://scubaboard.com/community/data/attachments/392/392087-b1ad0b38162a3d61ec4e88253997f6c7.jpg)
It takes around half an hour, no more, to build it.
special cables had stupid price around 60$ per small piece of plastic....
I take:
Digital Optical Fiber Audio Cable SPDIF Toslink (price could be from 2-4$)
Heat Shrink tubeS (price for set of different diameters is around 1-2$)
knife (I had)
Lighter or Hot air solderer
Cut optical cable to the desired lenght (cut away connectors anyway)
Put on thinest tube, with length 2-4 cm (1/2 till 1 inch), heating it.
Than more thick, and shorter. Heat it.
etc.
at final steps:
Cool it well, than cut front edge with sharp knife.
![i-717.jpg i-717.jpg](https://scubaboard.com/community/data/attachments/392/392083-6fcb1b3e5eaf21bdb574392cda879d1a.jpg)
![i-719.jpg i-719.jpg](https://scubaboard.com/community/data/attachments/392/392084-c39bc8c539d9813bf5ccf75665c87d10.jpg)
Heat it again, and then push it in-to connecting hole and bent over, to fit exact size.
![i-720.jpg i-720.jpg](https://scubaboard.com/community/data/attachments/392/392085-c58fafb8bd7607c50ca37357b0bf27a9.jpg)
Also can bent hot cable.
![i-715.jpg i-715.jpg](https://scubaboard.com/community/data/attachments/392/392081-a8e133cef5127d447bd9cb38b81df05f.jpg)
![i-716.jpg i-716.jpg](https://scubaboard.com/community/data/attachments/392/392082-5e7c592bf7c1c6703d16c2c9184aeefc.jpg)
Wait untill it be cold, and use and be happy
If you got bad selfmade connector - just cut away, and repeat
![i-714.jpg i-714.jpg](https://scubaboard.com/community/data/attachments/392/392086-d56b6f45a881ec451320a0d8c788751b.jpg)
![i-718.jpg i-718.jpg](https://scubaboard.com/community/data/attachments/392/392087-b1ad0b38162a3d61ec4e88253997f6c7.jpg)
It takes around half an hour, no more, to build it.