thibert
Registered
This take about 30 minutes to make two snoots, light weight and easy to do. Supplies need are one 3inch flexible PVC coupling,two-3 inch white PVC caps,two- 3/8 plastic toilet supply lines and two rubber washer/shock absorbers to hold supply lines on(this way you can remove them for travel)
![3 inch.jpg 3 inch.jpg](https://scubaboard.com/community/data/attachments/158/158360-042661decefecb7c1254f0006f7a5209.jpg)
![3 inch pvc cap.jpg 3 inch pvc cap.jpg](https://scubaboard.com/community/data/attachments/158/158361-55c4299bc6193251287211179771193d.jpg)
![rubber washer shock absorber .jpg rubber washer shock absorber .jpg](https://scubaboard.com/community/data/attachments/158/158362-a827f45950dee1e21a755825df9291cf.jpg)
![supply line .jpg supply line .jpg](https://scubaboard.com/community/data/attachments/158/158363-6f5d9c058a8dd31b517ece5e34214d8e.jpg)
Cut the 3 inch flexible coupling in half insert the 3 " caps in each piece pre drill a hole for the supply lines insert supply line from the inside and hold in place with the washer. I painter the inside of the white cap black.![2016-01-06 12.37.35.jpg 2016-01-06 12.37.35.jpg](https://scubaboard.com/community/data/attachments/158/158364-3d775ebcb180fd8d846eb840eeb5a9a3.jpg)
![2016-01-06 12.38.36.jpg 2016-01-06 12.38.36.jpg](https://scubaboard.com/community/data/attachments/158/158365-6d51196783ab33e01b3b4e020f08a6b8.jpg)
If you only have one strobe you could use two supply lines at different lengths that would give slightly different light levels from each.
![3 inch.jpg 3 inch.jpg](https://scubaboard.com/community/data/attachments/158/158360-042661decefecb7c1254f0006f7a5209.jpg)
![3 inch pvc cap.jpg 3 inch pvc cap.jpg](https://scubaboard.com/community/data/attachments/158/158361-55c4299bc6193251287211179771193d.jpg)
![rubber washer shock absorber .jpg rubber washer shock absorber .jpg](https://scubaboard.com/community/data/attachments/158/158362-a827f45950dee1e21a755825df9291cf.jpg)
![supply line .jpg supply line .jpg](https://scubaboard.com/community/data/attachments/158/158363-6f5d9c058a8dd31b517ece5e34214d8e.jpg)
Cut the 3 inch flexible coupling in half insert the 3 " caps in each piece pre drill a hole for the supply lines insert supply line from the inside and hold in place with the washer. I painter the inside of the white cap black.
![2016-01-06 12.37.35.jpg 2016-01-06 12.37.35.jpg](https://scubaboard.com/community/data/attachments/158/158364-3d775ebcb180fd8d846eb840eeb5a9a3.jpg)
![2016-01-06 12.38.36.jpg 2016-01-06 12.38.36.jpg](https://scubaboard.com/community/data/attachments/158/158365-6d51196783ab33e01b3b4e020f08a6b8.jpg)
If you only have one strobe you could use two supply lines at different lengths that would give slightly different light levels from each.