Search results

Thank you very much for your trouble. It seems to me that what defines the depth at which the purge button is pressed is the lip eight on measurement 6. Could you check on your reg if that's where the part ends travel when pressed against the reg? Thank you.

Hi. Sorry for my lousy finger painting on those. If you could please provide measurements in both GAS side and NO GAS. 1 and 2 are depth from base to outer lip. 3 os thickness of the lip. 4 and 5 are full with and heigh measured from the outside of the lip. And finally 6 is the distance from the...

If anyone has the flow no flow tool that can take the depth of each side I can make a 3D design of it so we can 3D print :D

I was using paraffin wax until I read that since paraffin wax is made from petroleum, like neoprene, and could degrade the neoprene then I opted for bees wax. Hence why I made that stick

Deodorant stick's are significantly larger than that design. The point in doing is the fact that its very thin, enough to fit the neoprene slaps around the zipper. Its almost as wide as the zipper itself. As per the picture in my second reply, its like 14mm wide

Thank's @rob.mwpropane I did not design a cap as you can always retract the wax back to the stick. Didn't think it would be needed. Here you go. Cheers

I wonder if the slightly caustic nature of soap could affect the brass long term.

From what I read, wax can be used on any zipper. Labello tube is round and with a wide diameter, hard to fit between the neoprene flaps around the zipper, hence why I designed it oval.

Hi! So, as per the title. There are quite a few options in terms of zipper lubricants but when it comes to solid lubricants, they usually only sell a lump of paraffin wax that is not very convenient to handle and apply on zippers. Too small the hold and rub on and too large to fit between the...

I work in electronics and if you want I can have a look and try to see if it's fixable. I wont charge you anything to try if you are willing to pay for shipping to Portugal. Cheers

Up that. I bought one and am pleased with it. Read around about some issues with it but i never experienced any problem. Cheers

Nice to hear that. I still have to make some improvements on the software (added functionality via smartphone/laptop connection) and there will be a functionality for dive shops that might want to resell to add their own logo to the display for a couple of seconds every time it turns on. The...

Hi, Parts and software files won't be available as this is part of an ongoing commercial project. But i can provide the 3D case files if those are usefull. Electronic wise it's not fully standard off the shelf parts and a custom PCB might be the solution in the future. If i can get some minimum...

Just another update. Measure of 100% oxygen successful. Cheers

PLA as the rest of the case. You can see it in the first picture. I printed it in white because it was the filament I had

Hello. I have been busy for the last few months and haven't had the opportunity to give feedback on my project. Today I finished my 2nd prototype of the simplest type of analyser, plain O2 with measurement with given mod at ppO2 of 1.4 and 1.6. It is a simple but apparently reliable analyser and...

As in another discussion about Undepleatable oxygen sensors I think it would be more appropriate to continue the topic here. Previous posts on this thread: Thread So I finally got to order some parts for my first prototype. A bit different from the initial project but I can start simpler and...

So, to continue my venture on this analyzer, I decided to create a new thread on a more appropriate section found here Cheers

I really wonder why there isn't much feedback on those. Any how, UTD isn't sold in Europe so that's a no for me. I'm still on the fence tough if i should go for negative fins or neutral/positive fins... Currently dive 7mm wetsuit, but plan on buying a drysuit in the near future.

AG? I just found this video (although probably biased) reviewing those fins and comparing, maybe someone more experienced could comment on that?