Search results

  1. J_Rod

    Question PPX Air Pressure Response Slow at Air ON/OFF

    PPX not used for over 6mos....When doing a gear check for the next dive, I noticed that the air pressure only slowly went up over 5 minutes, but ended up with an accurate pressure. Pressure change came down the same rate as it went up, after air turned off and pressure purged. Is this a known...
  2. J_Rod

    MK20 UL with 3 Vent Saddle

    Was the MK20 UL subject to the same MK20 recall to replace the yoke nut and saddle? Thanks in advance.
  3. J_Rod

    Mantis 2.0 and Transmitter Pairing

    Anyone else have an issue with pairing? I am waiting on another transmitter, just in case it is bad. Battery is good, but it is an older "triangular" transmitter, with no LED on the end, so I have no idea if it is even activating when pressurized. Also, is there a trick to Cradle/USB...
  4. J_Rod

    Scubapro Watch Cradle Part Numbers

    Are the cradles for the Chromis, Mantis, Mantis2, the same cradle? I think they are the same part number, which suggests there would be no difference, yet they have different prices.
  5. J_Rod

    R190 Parts?

    I like to restore older SP dive equipment (therapeutic hobby :)). I currently have a MK2/ R190 set that I am piecing together. It came to me, post Irma, with no cover, diaphragm, or ring. I have manged to find these parts (on that e place), but the cover does not have a purge button with it...
  6. J_Rod

    SP Part Number

    Does SP sell a combo LPI Hose/Removable AIR2 QD rather than buying the 2 separate parts? I have the hose (01.310.026) and the QD (21.009.006) Just wondering if there is a SP part number for the combo that includes both, and what the list is? If there is a resource I can use to look it up...
  7. J_Rod

    Pro Plus 2 Data Cable?

    Anybody know who may have the usb cable for a Pro Plus 2 (NOT 2.1)?? JoeDiver said they had one...sent an email after I ordered it, that it'd be 2 weeks, because they didn't actually stock one...over 1mo later, I still had no cable. They were kind enough to cancel the order for me. I know...
  8. J_Rod

    Scubapro MK 20 creeping badly

    Hi Gurus, I have a MK20 that cycles from 100# to 135# IP. It gets back to 135 in about 3 seconds....BUT, then it will creep to as high as 160# over 30 minutes, then it stabilizes,but over 150#....I have read about the piston evolution of the MK20 series, and know that I have the brass tip...
  9. J_Rod

    Twin Jet Full-foot Fin Warranty

    Hello SP Reps, I have a pair of these fins....LOVE them....problem is, the pull tabs on the backs were apparently not meant to be used, because BOTH have torn off. I have cut the jagged "V" into a uniform "U" and have been using the fins for about 5 dives. Not sure how much more the heal of...
  10. J_Rod

    Help with MK10 Service

    I have started to service a MK10 I got off of EBAY...I cannot figure out how to get the internal (piston stem) o'ring into place. I have a MK10 o'ring installation tool with a bullet but cannot get the internal o'ring past the bottom of the main housing on the seat side. It looks impossible to...
  11. J_Rod

    Cleaning/Deoderizing D400...

    I just got another D400 (my third) I realized why I got it so cheap after it arrived...It smells/tastes like it has been buried an ashtray for the last 10 years...Any advice on something safe to soak it in?? Tried a mild vinegar/water solution...afraid to leave it in for too long...new...
  12. J_Rod

    Breathability Test

    I have a MK25 and a few different SP 2nd stages ("newer" D400, "older" D400, 1st Gen S600, and an A700)...I was wondering if using all 4 LP ports and breathing each Reg (in a pool) is a valid test to determine which 2nd performs best or if there would be any difference in pressures between ports...
Back
Top Bottom