We design, manufacture, test and regularly use bungee adapters for diving computers and compasses. At the moment, more than 70 models have been created. PETG plastic, marine grade bungee, stainless steel screws. Worldwide free shipping.
If your model is not listed, please measure all the sizes...
We are a large diving team, we design, manufacture, test and regularly use bungee adapters for diving computers and compasses. At the moment, more than 80 models have been created. PETG plastic, marine grade bungee, stainless steel screws. Worldwide shipping.
We design and manufacture bungee mount adapters for diving computers and compasses. At the moment, more than 60 models have been created. This is our new product designed for AP Diving 2020VISION Display.
D9tx bungee adapter
This is 3d printed bungee mount adapter.
Made of black, red or yellow PETG plactic.
Stainless still screw. Reliable rubber cord.
installation video
We just developed bungee adapters and holders for for Suunto computers
3d printed PETG
Black, yellow, red colors
$20 for any one with free shipping world wide on our site www.rovthruster.com
Our Amazon, eBay
D9tx/dx will be soon
What is your favorite dry suit leaks, but the hole is not visible?
You can find and fix it just in 60 second!
We already use this method for our dive team.
Apply UV spray the outside of the drysuit.
Spray is designed to search for the smallest damage and easily penetrates through the holes in a...
We used:
laser module 200 mW
Laser Line Lens 30°
Clear acrylic tube 60 mm OD 5 mm w
Aluminum tube 50 mm OD
Motor Gear 6v 60RPM
Round Holder for 3x 3.7V 18650 Battery
Magnetic Contact Reed Switch
Tested at 5 bar, run time 10 hours.
Seen under water at a great distance and is very effective...
I bought 5 underwater connectors and test them in my hydrostatic chamber within 24 hours under 20 bar with salt water. No damage or leakage. Of course it shouldn't be connected underwater but I can disconnect it underwater at any time. So I made DIY drysuit, canister and light e/o connectors...
I made 4 washers from 10mm acrylic. Washers were glued and then turned on a lathe.
Resulting cone was stuck to Meikon 16mm box.
Hand made dome 10 cm diameter fixed by aluminum ring.
Now I can use my box with SEL-16F28 + VCL-ECU1 or 18-55.
15W amplifier + 15W speaker + FM modulator + 12V 7Ax2 + an old pressure pot = underwater speaker.
We have tested it at 10 meters. The music is very well heard at a distance more than 30 meters and lyrics clearly audible at a distance of 15 meters...
The pattern for that I made from some factory vest.
6 meters of carbon heater tape placed on back and both sides.
Because of big length it provides uniform heating of body.
Tape connected in parallel 6x1m. It takes about 3A under 12V (36W).
Wires sewed to carbon tape to make a good and...
I bought a carbon flex tape and have sewed it into an ordinary insulated fleece gloves.
For every glove I used 145 cm of carbon. It powered by 12 V. Current is about 1,5A for one. I've tested it 50 min in water +1/+3. My fingers were absolutely warm.
We made it from a trolling motor 12V 15A 18 lbr.
The shaft tightened by ceramic seal.
Powered by three SLA battery 12V 7Ah.
Housing is a PVC pipe 200mm.
How do you usually evaluate underwater visibility?
We had made a test to use the Secchi disk with a ruler directly underwater.
At first we asked a few divers to evaluate the current visibility by eyes. They estimated it about 60-80% from Secchi.
Now we will make continuous measurements to...
An ordinary 2.0 mL syringe can provide pressure up to 25 bar.
It's quick, safe and very convenient to use:
http://www.youtube.com/watch?v=x5CVSzOu4uw&feature=youtu.be
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.