I'm seeing a good amount of S500-555/600 etc.. with a plastic air barrel that has either a split or some cracking where the metal threads meet the plastic barrel.
I know if you crank on the nut too much it can crack the barrel....so I always am delicate not to over tighten the air barrel nut...
Is this possible? I see guys with CCRs dive it in their dill but with my mix calculator I don't see how it is possible with a partial blend? It says they have to remove -15 02 PSI.
I'm assuming they just drop the helium in the tank and top with air? The -15 02 is too small or is there...
Hey guys just trying to get the word out on this. Blue Water Divers is having a great event to benefit some of our real heroes on April 17th & 18th. 100% goes to SUDS and nothing goes in the pockets of BWD. Cheap good gear for sale, Raffles, and some giveaways.
Below is the link giving more...
I posted this in the DIY forum, but thought I might get some bites here.. Any help would be appreciated..
I got quoted a few places for $6 bucks a pound. I read that you need ~20lbs to tumble a tank $120 total for media?
I also found on McMaster they sell it pretty cheap, but I dont...
I got quoted a few places for $6 bucks a pound. I read that you need ~20lbs to tumble a tank $120 total for media?
I also found on McMaster they sell it pretty cheap, but I dont know what size. Any recommendations on size/mesh?
Thanks for the help. Im building a tumbler and before I...
Have a set of 3500 PSI steel 100 with the older style 7/8 UNF neck (smaller size)
They are currently set up as doubles with right/left hand valves. I'm breaking them down into singles and need some help.
I found the right hand thread plug pretty easily... (with wheel on left.. just like a...
Enjoy. I'm too cheap to purchase log paper. And besides I don't like the fields that are on the traditional log book paper So I just put the fields that I want.
Hope someone can use this and enjoy.
Dive safe
Rich
hello Folks..
Scubapro has two tiny o-rings on their s-wing poppet. Its Scubapro part #010050363
I seen in a prior post its either 2.5x1mm or 2.2X1mm. Is this 2.5MM OD & 1MM ID? I think this is what it means. I looked on McMaster's website and could not find them.. looks like they...
have a 2 part question.
1. am I adjusting my regs right
2. is the seat bad on my s550.
I have a S550 that I can't dial in with the dual drive adjusting tool.
IP is ok....
I read that you place it on the dual drive tool, loosen it up so it free flows and then just give it 1/12th turn...
Thanks again everyone for your help in the past.
Few questions on the nylock nut on the scubapro 2nd stage.
In the manual it says to disregard and throw out the nut every time you take it off. Is there anything special about this nut? Meaning I have a local shop that caries a bunch of odd...
Might be a dumb question, but I can't see how this thing works.
in the scubatools website...p-591-mouthpiece-adapter-assembly-acetal
SKU: 26-300-400
Is there a hole in the back the attachment so you can put your mouth up to it and take a breath to see the cracking pressure on the guage...
Nice.. I read a bunch on this board and on the net about scubapro kits.... seems like only black market you can get them..
Scubapro has pretty much locked you down to get HP seats and misc scubapro parts from your Local LDS only.
Anyone know where I can buy the poppets, HP seats (have a...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.